Rooms that never get warm
Undersized equipment, bad ducts, or a failing boiler all leave rooms cold. Sizing from a load calculation and checking the distribution system is how that is fixed.
Furnace, boiler, or heat pump — matched to your home and your ducts
Heating System Installation Denver for Your Home
A heating install planned in fall usually comes down to one choice: furnace, boiler, or heat pump. Each heats differently, and the right one depends on the house, its ducts or radiators, and how the rooms are used. Call (720) 806-7634 to talk it through.
Call any time
Call to book
Call (720) 806-7634 and talk through the home. Lion Tech Home Services explains furnace, boiler, and heat pump options for the house as it stands.
Call Now (720) 806-7634 → Open 24 hours · 7 days a week
Careful work. Honest options.
About this service
Heating System Installation in Denver: What the Job Involves
A heating system installation replaces or adds the equipment that warms a home: a gas furnace with ductwork, a boiler feeding radiators or radiant floors, or a heat pump that heats and cools. The job is sizing, setting the equipment, connecting fuel or power, and testing the system room by room.
Denver homes vary widely: 1920s bungalows with radiators, mid-century ranches with ducts, newer builds with tight envelopes, and the heating system has to fit the house it serves. A furnace suits ducted homes, a boiler suits radiator and radiant homes, and a heat pump suits homes that want heating and cooling from one system. Sizing from a load calculation, at Denver altitude, is what makes any of them work.
- ✓ Furnace, boiler, or heat pump
- ✓ Sized from a load calculation
- ✓ Ducts or radiators checked
- ✓ Tested room by room
What's included
What Our Heating System Installation Includes
Every install runs the full scope from sizing to testing, whatever system is chosen.
✓
Load calculation
Rooms are measured, insulation and windows are checked, and the heating load is worked out before equipment is chosen. The size follows the house, not a rule of thumb.
✓
System choice, explained
Furnace, boiler, and heat pump options are laid out for the home, with the trade-offs explained, including what each one means for existing ducts or radiators.
✓
Equipment and materials
The visit covers the heating unit, thermostat, venting or refrigerant lines, condensate drain, and wiring, matched to the load calculation.
✓
Permits and inspection
Mechanical and electrical permits for the City and County of Denver are handled and the inspection is arranged.
✓
Ducts or radiators checked
The distribution system is looked over, ducts for forced air, radiators and piping for boilers, and what needs attention is flagged before the new system runs.
✓
Testing and walkthrough
The system is tested at every register or radiator, safety controls are checked, and the thermostat and filter routine are walked through.
How it works
Our Heating System Installation Process
01
Visit and measure
The house is walked, rooms are measured, insulation and windows are checked, and the existing heating system, ducts or radiators, and electrical panel are looked at.
02
Choose the system
Furnace, boiler, and heat pump options are talked through for the home, and what each one would mean for comfort and running costs.
03
Permits and prep
Permits are filed, equipment is ordered, and floors and the work area are protected before install day.
04
Install day
Lion Tech Home Services sets the new equipment, connects fuel or power, vents or runs refrigerant lines, and ties into the existing ducts or radiators.
05
Test and walkthrough
Every room is tested, safety controls are checked, and the controls are walked through. The system is left running and holding temperature.
Tools & methods
Tools and Methods We Use
The instruments that confirm a new heating system is set up right, not just switched on.
Manifold gauge set
Checks refrigerant charge on heat pump installs against the manufacturer's spec.
Multimeter
Verifies electrical connections, controls, and safety circuits on the new system.
Combustion check
Tests burner operation and venting on gas furnace and boiler installs.
Thermometer and airflow checks
Room-by-room readings confirm heat is reaching every part of the house.
Vacuum pump and micron gauge
Prepares refrigerant lines on heat pump installs before charging.
Leak detector
Checks gas and refrigerant connections for leaks before the system is handed over.
Typical jobs
Before and After
An old furnace in a ducted home
Before
A furnace past its useful life left the house uneven, cold bedrooms, a warm living room, and attention needed every winter.
After
A new furnace, sized from a load calculation with the ducts checked, now heats the house evenly and the repair calls have stopped.
Radiators in a 1920s bungalow
Before
A bungalow with radiators had a boiler that rattled, leaked at a valve, and left one radiator cold every winter.
After
A new boiler with the radiators bled and balanced now heats every room, and the rattling and leaks are gone.
A home that wanted heating and cooling
Before
A house with a furnace and no cooling sweltered through July, and the owners were weighing an AC on top of the furnace.
After
A heat pump replaced the furnace as the main system, giving heating and cooling from one unit, with the gas furnace kept as backup for the coldest nights.
Problems we solve
Problems a New Heating System Solves
A heating system at the end of its life shows the same signs in most Denver homes. A replacement takes on these four.
Ask a pro →↗
Repairs every winter
When a system needs work every season, the repairs add up. A new system resets the clock, and an honest word is given when repair stops making sense.
Noisy, rattling operation
Banging radiators, a roaring burner, or a fan that grinds all point to wear. A new install removes the worn parts and the noise with them.
Heating but no cooling
A furnace-only home has nothing for July. A heat pump covers both seasons from one system, and a dual-fuel setup keeps the furnace for the coldest nights.
About Lion Tech
Denver HVAC, Open Around the Clock
Lion Tech Home Services installs heating systems for Denver homes from 7575 E 29th Pl #4052, furnace, boiler, and heat pump.
Customer reviews
What Denver Homeowners Say About Our Installs
Lion Tech Home Services holds a 5.0-star rating from 11 Google reviews.
★★★★★
“Martin was great! Timely, knowledgeable, and his experience showed. He was able to fix our HVAC that had been having trouble on and off for awhile. Pricing was good and reasonable! Would certainly recommend!”
J
JulieGoogle review
✓ VerifiedIt depends on what the house already has. Ducted homes suit furnaces and heat pumps; radiator and radiant-floor homes suit boilers; homes that want heating and cooling from one system suit heat pumps. The house is looked at and the options are talked through before anything is recommended.
From a load calculation that accounts for room sizes, insulation, windows, and Denver's altitude, not from square footage alone. The right size holds temperature in January without short-cycling.
Most residential installs take a day or two, depending on the system and whether ducts, piping, or electrical work is needed. The schedule is confirmed before work starts.
The old equipment is removed and the work area is cleared as part of the job. Refrigerant is recovered rather than released, and old equipment is taken away.
Ready when you are
Plan Your New Heating System
Call (720) 806-7634 and talk through the home. Lion Tech Home Services will look at the house, the ducts or radiators, and the options, and give a quote for the work.
Call (720) 806-7634 →
Request an appointment
Contact Lion Tech Home Services
Lion Tech Home Services, Denver — call (720) 806-7634, open 24 hours.